Topic listResearch writingEngineering & technology

Electrical and electronic engineering project topics: renewable power, power electronics, embedded control and flexible devices

Thirty electrical and electronic engineering topic ideas, checked and condensed into twenty topics in five themes, each reshaped into a question one project can answer, with the design and data it would need.

What you will learn

  • Identify five active areas of electrical and electronic engineering where a master's or doctoral project can add evidence
  • Turn a broad label such as "wireless power" into a measurable research question
  • Choose between simulation, bench experiment and field measurement for an EEE topic
  • Explain why wide bandgap devices are changing power electronics design questions
  • Test a topic for feasibility against equipment, data and safety constraints

What you will unlearn

  • A topic is a subject heading such as "OLEDs" or "control systems".A topic becomes researchable only when it names a device or system, a variable to measure and a comparison.
  • Simulation results alone settle a power electronics question.Simulation should be validated against measurement or published data, and its assumptions reported.
  • Silicon is still the obvious default for every power device project.Silicon carbide and gallium nitride devices now compete in many converters, so the device choice is itself a research question.

Skills you will practise

  • Topic scoping
  • Simulation and modelling
  • Bench measurement
  • Comparative experimental design
  • Reliability testing
  • Laboratory safety planning

How to use this list

This list is for master's and doctoral researchers in electrical and electronic engineering (EEE) who need a project topic.

Treat every row as a starting point. Before you commit, check what equipment, software licences and data your department can give you, and search for studies published in the last three years. Related engineering pages: engineering dissertation titles and mechanical engineering topics.

Theme 1: Renewable generation and power systems

Power systems research has shifted from large synchronous machines towards networks dominated by converters, solar and wind. That shift makes classic questions (tracking, inverter choice, transmission, transients) worth asking again with current devices and data. Wide bandgap converters are now being reviewed specifically for microgrids, which shows how quickly the device layer is changing (Burmester et al., 2026).

Theme 1 topics: renewable generation and power systems
TopicPossible research questionLikely design and dataWhy it matters now
Dual-axis solar trackingHow much more energy does a dual-axis tracker deliver than single-axis and fixed mounting at one site, and does the gain cover its extra cost and energy use?Side-by-side field measurement over several months, or a validated model with local irradiance dataTracking gains depend strongly on climate and latitude, so local evidence is needed
Micro-inverters versus string inverters for rooftop PVUnder partial shading, which architecture yields more energy, and what are the efficiency and reliability trade-offs?Bench or rooftop comparison with controlled shading; efficiency curves; failure data where availableInverter choice drives yield and lifetime cost in small PV systems
Voltage-source-converter HVDC linkHow does a VSC-HVDC link respond to an onshore AC fault, and which control settings limit the disturbance?Simulation in an established power system tool with a published benchmark networkHVDC is the usual route for connecting distant offshore wind
Switching transients with inverter-based generationHow do capacitor-bank and breaker switching transients change as inverter-based generation rises in a distribution network?Electromagnetic transient (EMT) simulation of a benchmark feeder, varying the share of inverter-based generationProtection settings designed for synchronous machines may not suit converter-rich networks

Theme 2: Power electronics and devices

Silicon carbide (SiC) and gallium nitride (GaN) devices switch faster and with lower losses than silicon, which allows higher frequencies and smaller passive components; SiC is generally preferred above about 650 V and GaN below it, although the devices still cost more than silicon (Kumar et al., 2022). Comparing a silicon IGBT with a SiC MOSFET in the same circuit is a well-defined experiment (Kinyua & Aoki, 2025). Reliability is a live question too: in one modelling study of a photovoltaic string inverter, the GaN device showed about five times more plastic energy dissipation in its die attach under cloudy conditions than a SiC MOSFET, despite lower losses, which the authors attributed to its smaller package (Van De Sande et al., 2020).

Theme 2 topics: power electronics and devices
TopicPossible research questionLikely design and dataWhy it matters now
Silicon versus wide bandgap devices in a converter stageHow do switching loss, efficiency and junction temperature compare when a Si IGBT is replaced by a SiC MOSFET (or a GaN HEMT) in the same converter?Double-pulse tests and efficiency measurement on one test board; thermal imaging or thermal modelDevice choice is now a design decision, not a default (Kumar et al., 2022; Kinyua & Aoki, 2025)
Output ripple in a DC-DC converterWhich combination of switching frequency, filter design and control method minimises output ripple for a given efficiency target?Simulation followed by a prototype buck or boost converter with oscilloscope measurementRipple limits sensitive loads such as sensors and processors
Resonant inductive wireless power transferHow do efficiency and delivered power change with coil distance and misalignment, and which compensation network is most tolerant?Bench rig with measured coil parameters; comparison of two compensation topologiesWireless charging is spreading from phones to vehicles and implants
Thermomagnetic energy conversionCan a bench-scale thermomagnetic generator using a magnetic phase-change material produce measurable power from low-grade heat, and what limits it?Model of the magnetic and thermal cycle, then a small proof-of-concept rig if materials are availableLow-grade waste heat is plentiful but hard to convert

Theme 3: Control and embedded systems

Many good EEE projects combine sensing, computation and actuation in one small system. Framing such a system as a cyber-physical system, with layers from data acquisition to decision-making, helps you decide what to build and what to measure (Lee et al., 2015). For connected devices, a reference architecture gives a shared vocabulary for sensing, networking and application domains (ISO/IEC, 2024).

Theme 3 topics: control and embedded systems
TopicPossible research questionLikely design and dataWhy it matters now
PID versus model predictive control of a DC motor driveDoes model predictive control improve speed tracking and disturbance rejection enough to justify its computational load on a low-cost microcontroller?Hardware-in-the-loop or bench experiment with identical load steps; tracking error and execution timeLow-cost processors now make advanced control practical in small drives
Finite-state-machine controller on an FPGACan a safety-relevant controller (for example, traffic lights or a lift) be specified as a finite-state machine and formally verified before deployment?HDL design, simulation, formal property checking, then FPGA implementationFormal methods catch design errors that testing misses
Automatic control of vessel navigation lightsCan a low-power controller switch anchor and navigation lights automatically and report lamp faults reliably in marine conditions?Prototype with light and current sensing; environmental testing; fault-injection trialsSmall vessels often rely on manual switching and checks
Sensor fusion for a small mobile robotHow much does fusing wheel odometry, an inertial sensor and a low-cost range sensor reduce localisation error indoors?Repeated runs on a marked course with ground-truth positions; Kalman filter variants comparedAffordable autonomy depends on cheap sensors used well
Biometric authentication in an e-voting prototypeWhat false-acceptance and false-rejection rates, and what usability problems, does a fingerprint-based voter check show in a supervised trial?Prototype plus usability study with consenting volunteers; no real elections or real voter dataElection technology needs evidence on security and accessibility together

Theme 4: Signal processing and sensing

Signal processing topics work well when the signal, the hardware and the performance measure are all named. The four rows below each pair an algorithm or circuit with a concrete measurement, from audio noise to the voltage and current traces of an electrical discharge machine.

Theme 4 topics: signal processing and sensing
TopicPossible research questionLikely design and dataWhy it matters now
Real-time audio noise reduction on low-cost hardwareWhich noise-reduction method gives the best quality for its processing delay on a microcontroller or small DSP?Implementation of two or three methods; objective quality scores and listening tests on recorded speechHearing aids and voice interfaces need low delay and low power
Low-noise JFET input stage for an audio filterDoes a JFET input stage give lower noise and distortion than an op-amp-only design in an active audio filter?Circuit design, simulation, then prototype measurement of noise floor and total harmonic distortionHigh-input-impedance stages matter for sensors and audio sources
Embedded vision for early warningCan an edge device detect smoke or intrusion in camera images with acceptable accuracy and delay, while keeping images on the device?Public or consented datasets; compressed model on edge hardware; accuracy, latency and power measuredOn-device processing reduces bandwidth use and privacy risk
Monitoring electrical discharge machining from process signalsCan features of discharge voltage and current signals classify stable and unstable machining in real time?Signals logged on an EDM machine under planned settings; feature extraction and classificationProcess monitoring can cut scrap and electrode wear

Theme 5: Flexible, printed and optoelectronic devices

Device topics need access to fabrication or characterisation facilities, so confirm these first. The rows below are deliberately narrow: each tests one property of one device type under stated conditions.

Theme 5 topics: flexible, printed and optoelectronic devices
TopicPossible research questionLikely design and dataWhy it matters now
Printed interconnects in flexible hybrid electronicsHow does the resistance of printed conductive tracks joining silicon chips change under repeated bending?Printed test structures; cyclic bending rig; resistance logged against cycle countFlexible hybrid devices combine printed tracks with conventional chips
3D-printed conductive hydrogel strain sensorsHow stable are the conductivity and sensitivity of a printed conductive hydrogel sensor over repeated strain and drying?Fabrication of sensor samples; cyclic strain tests; humidity-controlled ageingSoft sensors are needed for wearables and soft robotics
OLED test devices under drive conditionsHow do drive current and temperature affect luminance decay and efficiency of OLED test devices?Accelerated ageing of fabricated or purchased test devices; luminance and current-voltage measurementLifetime remains a limit for some OLED applications

How to test a topic before you commit

Use the FINER criteria: feasible, interesting, novel, ethical and relevant (Hulley et al., 2013). In EEE, feasibility usually decides the matter. List the equipment, licences and components you need, check lead times, and agree laboratory safety arrangements for high voltage or high current work before you start. Plan how you will store and share data and code; research funders such as the EPSRC expect research data to be preserved and made accessible where appropriate (EPSRC, 2022).

For the wider process, see how to choose a PhD topic, how to select a PhD topic and PhD topic selection support.

Common mistakes

  • Choosing a subject heading ("OLEDs", "control systems") instead of a question with a measurable outcome.
  • Relying on simulation alone, without validation against measurement or published data.
  • Planning a prototype that needs equipment or components you cannot obtain in time.
  • Comparing two designs under different conditions, so the comparison is not fair.
  • Leaving high-voltage safety approval and data management until the experiments are due.

Key takeaways

Your next step

Want to apply this to your own study?

  1. 1Tell us your topic, data and deadline
  2. 2A subject mentor reviews your work with you
  3. 3You get a plan and a quote
PhD topic selection

References

  1. Burmester, D., Rayudu, R., & Brent, A. (2026). Applications and implications of wide-bandgap technologies in microgrids: A review. Energies, 19(5), 1126. https://doi.org/10.3390/en19051126
  2. Engineering and Physical Sciences Research Council. (2022, March 31). EPSRC policy framework on research data: Expectations. UK Research and Innovation. https://www.ukri.org/about-us/epsrc/our-policies-and-standards/policy-framework-on-research-data/expectations/
  3. Hulley, S. B., Cummings, S. R., Browner, W. S., Grady, D. G., & Newman, T. B. (2013). Designing clinical research (4th ed.). Wolters Kluwer Health/Lippincott Williams & Wilkins. https://search.worldcat.org/title/830019201
  4. International Organization for Standardization & International Electrotechnical Commission. (2024). Internet of things (IoT): Reference architecture (ISO/IEC Standard No. 30141:2024, 2nd ed.). https://webstore.ansi.org/standards/iso/isoiec301412024
  5. Kinyua, J. M., & Aoki, M. (2025). Comparative dynamic performance evaluation of Si IGBTs and SiC MOSFETs. Energies, 18(24), 6540. https://doi.org/10.3390/en18246540
  6. Kumar, A., Moradpour, M., Losito, M., Franke, W.-T., Ramasamy, S., Baccoli, R., & Gatto, G. (2022). Wide band gap devices and their application in power electronics. Energies, 15(23), 9172. https://doi.org/10.3390/en15239172
  7. Lee, J., Bagheri, B., & Kao, H.-A. (2015). A cyber-physical systems architecture for Industry 4.0-based manufacturing systems. Manufacturing Letters, 3, 18-23. https://doi.org/10.1016/j.mfglet.2014.12.001
  8. Van De Sande, W., Alavi, O., Nivelle, P., D'Haen, J., & Daenen, M. (2020). Thermo-mechanical stress comparison of a GaN and SiC MOSFET for photovoltaic applications. Energies, 13(22), 5900. https://doi.org/10.3390/en13225900

How to cite this article

Choose your referencing style, then copy. Check your university's or journal's guide for local variations.

PhD Research Lab Academy. (2020, March 10). Electrical and electronic engineering project topics: renewable power, power electronics, embedded control and flexible devices. PhD Research Lab. https://www.phdassistance.com/engineering-technology/list-all-topics-and-structure-to-write-an-assignment-for-electric-and-electronic/

PhD Research Lab Academy. “Electrical and Electronic Engineering Project Topics: Renewable Power, Power Electronics, Embedded Control and Flexible Devices.” PhD Research Lab, 10 Mar. 2020, www.phdassistance.com/engineering-technology/list-all-topics-and-structure-to-write-an-assignment-for-electric-and-electronic. Accessed [access date].

PhD Research Lab Academy (2020) Electrical and electronic engineering project topics: renewable power, power electronics, embedded control and flexible devices. PhD Research Lab. Available at: https://www.phdassistance.com/engineering-technology/list-all-topics-and-structure-to-write-an-assignment-for-electric-and-electronic/ (Accessed: [access date]).

PhD Research Lab Academy. “Electrical and Electronic Engineering Project Topics: Renewable Power, Power Electronics, Embedded Control and Flexible Devices.” PhD Research Lab. March 10, 2020. https://www.phdassistance.com/engineering-technology/list-all-topics-and-structure-to-write-an-assignment-for-electric-and-electronic.

PhD Research Lab Academy, ‘Electrical and Electronic Engineering Project Topics: Renewable Power, Power Electronics, Embedded Control and Flexible Devices’ (PhD Research Lab, 10 March 2020) <https://www.phdassistance.com/engineering-technology/list-all-topics-and-structure-to-write-an-assignment-for-electric-and-electronic> accessed [access date].

PhD Research Lab Academy. Electrical and electronic engineering project topics: renewable power, power electronics, embedded control and flexible devices [Internet]. PhD Research Lab; 2020 Mar 10 [cited [access date]]. Available from: https://www.phdassistance.com/engineering-technology/list-all-topics-and-structure-to-write-an-assignment-for-electric-and-electronic/

PhD Research Lab Academy, “Electrical and electronic engineering project topics: renewable power, power electronics, embedded control and flexible devices,” PhD Research Lab, Mar. 10, 2020. [Online]. Available: https://www.phdassistance.com/engineering-technology/list-all-topics-and-structure-to-write-an-assignment-for-electric-and-electronic. [Accessed: [access date]].

@online{list_all_topics_and_structure_to_write_an_assignment_for_electric_and_electronic_2020,
  author = {{PhD Research Lab Academy}},
  title = {{Electrical and electronic engineering project topics: renewable power, power electronics, embedded control and flexible devices}},
  organization = {PhD Research Lab},
  date = {2020-03-10},
  url = {https://www.phdassistance.com/engineering-technology/list-all-topics-and-structure-to-write-an-assignment-for-electric-and-electronic},
  urldate = {[access date]}
}

This article is for learning. Use it to understand the method and cite the original sources above in your own work; do not copy or submit it as your own.

Electrical and electronic engineering project topicsNeed help applying it to your study?
PhD topic selection